Purpose: radiation source

Characteristics:

• radiation output power 1 W
• wavelength 533 nm
• beam output diameter 3 mm
• TTL – modulation (up to 1 kHz)

Responsible officer Егоров Роман Игоревич

Purpose: radiation source

Characteristics:

• radiation output power 5 W
• wavelength 533 nm
• beam output diameter 3 mm
• TTL – modulation (up to 1 kHz) 

Responsible officer: Егоров Роман Игоревич

Purpose:
programmable power supply.

Characteristics:

• output frequency 45-65HZ
• output voltage 0-32 V
• output current 0-32 A.

Responsible officer: Егоров Роман Игоревич

Purpose:
grinding of solid materials.

Characteristics:

• Max. initial particle size 10 mm, max. productivity up to 5 l/h.
• final degree of grinding d50 < 40 µm, ring sieves 0.08 – 6 mm
• speed adjustment from 6000 to 20000 rpm
• efficient cooling of the grinding chamber due to exceptionally intensive air supply
• highly reliable, wear-resistant stainless steel rotor
• crushing chamber made of stainless steel or PTFE coated with practical quick-release lock

Responsible officer: Романов Даниил Сергеевич

Purpose:
separation of crushed materials during sample preparation and determination of particle size distribution.

Characteristics:

• vibration amplitude 0.25–1.5 mm;
• motor shaft rotation speed 1350 rpm;

Responsible officer: Романов Даниил Сергеевич

Purpose:
maintaining a constant temperature.

Characteristics:

• temperature range from -30 to +100 °C, provided through the use of coolant
• a mixture of propylene glycol and water in a ratio of 50/50, temperature deviation in the working container ±0.01 ° C)
• bath depth 320 mm
• viewing window size 104x270 mm

Responsible officer: Романов Даниил Сергеевич

Purpose:
dosing (pumping) of various volumes of liquid.

Characteristics:

• productivity 0.0002–600 ml/min
• engine rotation speed 0.1–100 rpm
• dispensed volume 0.01 ml – 9.9 l.

Complete with pump heads YZII25, YZII15,

Responsible officer: Ашихмин Александр Евгеньевич

Purpose:
measurement, registration or automatic control of temperature, as well as other physical quantities (pressure, humidity, level, flow, etc.) through one or two channels simultaneously.

Characteristics:

• input polling time no more than 1 second
• limit of basic reduced error 0.25–0.5%
• number of input devices 2

Responsible officer: Романов Даниил Сергеевич

Purpose:
Mixing viscous media and large volumes of liquid.

Characteristics:

• torque, H*cm: 294
• Max. volume, 150 l
• rotation speed, 60–600 rpm.

Responsible officer: Глушков Дмитрий Олегович

Purpose:
separation of heterogeneous liquid systems into fractions of different densities under the influence of centrifugal forces

Characteristics:

• Maximum rotation speed - 4000 rpm
• Rotation speed setting - digital with resolution of 10 rpm
• Standard rotor capacity - 12x20 ml
• Maximum centrifugal acceleration - 2325 g
• Timer setting time - from 1 to 99 minutes with discreteness of 1 minute

Responsible officer: Романов Даниил Сергеевич

Purpose:
determination of the rigidity index of the concrete mixture, production of control concrete samples in accordance with GOST 10181-2000; production of control samples of cement in accordance with GOST 310.4; production of control samples of asphalt concrete GOST 12801-98

Characteristics:

• vibration amplitude 0.35–0.5 mm
• type of vibrations – vertical
• load capacity up to 100 kg.

Responsible officer: Романов Даниил Сергеевич

Purpose:
simultaneous mixing of liquids in several containers

Characteristics:

• platform movement - reciprocating
• range of operating frequencies of platform oscillations - from 20 to 200 kol/min
• platform vibration range - 10 mm

Responsible officer: Романов Даниил Сергеевич

Purpose:
maintaining the temperature of the work area.

Characteristics:

• temperature control range -20…+200 °C
• instability of maintaining the set temperature ±0.1 °C
• inhomogeneity of the temperature field in the working area ±0.1 °C

Responsible officer: Пискунов Максим Владимирович

Purpose:
mixing of components (liquid–liquid; liquid–solid fine particles) under heating conditions.

Characteristics:

• rotation speed range of the magnetic armature is 600–2600 rpm.
• maximum volume of mixed composition 5 l
• maximum viscosity of the composition 1170 mPa s
• adjustable heater surface temperature +30…+120 °C

Responsible officer: Шлегель Никита Евгеньевич

Purpose:
supply of liquid through two autonomous channels.

Characteristics:

• Types of syringes used by volume, including 5, 10, 20, 30, 50/60 ml
• Memory for 33 types of syringes
• Bolus infusion function, “antibolus”
  
• Possibility of operation from AC mains or built-in battery
• Information contained in the stored records: injection rate, final volume injected, occlusion pressure, target volume, alarm type

Responsible officer: Шлегель Никита Евгеньевич

Purpose:
heating, maintaining a heated state, evaporation and drying of solutions, mixtures, samples and specimens.

Characteristics:

• operating temperature range of the heating surface: 40…400 °C
• instability of maintaining the set temperature: 5°C
• insulation resistance of mains supply circuits: not less than 2.0 MOhm
• maximum heat treatment time: 599 minutes
• The stove is powered from a 1-phase AC mains voltage (230±23) V, frequency (50±1) Hz
• stove power consumption: no more than 1500 W
• overall dimensions of the heating surface: 284×284 mm
• Overall dimensions of the plate: 290×260×130 mm.

Main building of TPU (Lenina Ave., 30), room 012

Responsible officer: Шлегель Никита Евгеньевич

Purpose:
heating, maintaining a heated state, evaporation and drying of solutions, mixtures, samples and specimens.

Characteristics:

• operating temperature range of the heating surface: 40…500 °C
• instability of maintaining the set temperature: 5°C
• insulation resistance of mains supply circuits: not less than 2.0 MOhm
• maximum heat treatment time: 599 minutes
• The stove is powered from a 1-phase AC mains voltage (230±23) V, frequency (50±1) Hz
• stove power consumption: no more than 1500 W
• overall dimensions of the heating surface: 284x224 mm
• overall dimensions of the plate: 290x260x130 mm

Responsible officer: Шлегель Никита Евгеньевич

Purpose:

performing heating, hardening, firing of various materials in air at temperatures from +300 °C to +1200 °C.

Characteristics:

• range of set temperatures: 100…1200°С
• operating temperature range: 300…1200°С
• error in reproducing the set temperature in the range 300…1200 °C: no more than ±10°C
• instability of maintaining temperature in the range of 300…1200 °C: no more than ±10°C
• internal diameter of the pipe: not less than 20±2, mm
• pipe length: not less than 250 mm
• heated pipe length: not less than 210 mm

Responsible officer: Антонов Дмитрий Владимирович

Purpose:
heating, maintaining a heated state, evaporation and drying of solutions, mixtures, samples and specimens.

Characteristics:

• operating temperature range of the heating surface: 40…500 °C
• measurement range of external temperature sensor: 0.1°C
• instability of maintaining the set temperature: 5°C
• insulation resistance of mains supply circuits: not less than 2.0 MOhm
• maximum heat treatment time: 599 minutes
• The stove is powered from a 1-phase AC mains voltage (230±23) V, frequency (50±1) Hz
• stove power consumption: no more than 1500 W
• overall dimensions of the heating surface: 284×220 mm
• overall dimensions of the plate: 290×260×122 mm

Purpose:
performing heating, hardening, firing of various materials in air at temperatures from +300 °C to +1200 °C.

Characteristics:

• range of set temperatures: 100…1200°С
• operating temperature range: 300…1200°С
• error in reproducing the set temperature in the range 300…1200 °C: no more than ±10°C
• instability of maintaining temperature in the range of 300…1200 °C: no more than ±10°C
• internal diameter of the pipe: not less than 50±2, mm
• pipe length: not less than 500 mm
• heated pipe length: not less than 400 mm

Responsible officer: Антонов Дмитрий Владимирович

Purpose:

performing heating, hardening, firing of various materials in air at temperatures from +300 °C to +1200 °C.

Characteristics:

• range of set temperatures: 100…1200°С
• operating temperature range: 300…1200°С
• error in reproducing the set temperature in the range 300…1200 °C: no more than ±10°C
• instability of maintaining temperature in the range of 300…1200 °C: no more than ±10°C
• internal diameter of the pipe: not less than 20±2, mm
• pipe length: not less than 250 mm
• heated pipe length: not less than 210 mm

Responsible officer: Антонов Дмитрий Владимирович

Purpose:
Mixing liquids, cleaning contaminants.

Characteristics:

• Supply voltage - 220 V/ 50-60 Hz
• Operating frequency - 35 kHz
• Volume - 2.8 l
• Digital timer - 1 - 99 min
• Digital thermostat - 15 - 70 C
• Power consumption - 250 W
• Generator power - 100 W
• Heater power - 150 W
• Number of emitters – 2
• Overall dimensions (LxWxH) - 260x160x250 mm
• Tank dimensions - (LxWxH) 240x135x100 mm
• Weight - 4.0 kg

Responsible officer: Шлегель Никита Евгеньевич

Purpose:

creating a local work area for sterile work, protecting personnel, product and the environment from possible contamination.

Characteristics:

• overall dimensions (W*D*H): 1200*770*1495, mm
• biological safety class according to GOST R EN 12469-2010: II
• class of installed high-efficiency HEPA filters according to GOST R EN 1822-1-2010: H14
• air cleanliness class in the working area according to GOST R ISO 14644-1-2017: ISO class 5
• efficiency of filter cleaning class H14 from suspended particles larger than 0.3 microns: 99.995%
• in operating mode, air flow speed at a height above 100 mm from the bottom edge of the glass: from 0.25 to 0.50 m/s

Responsible officer: Антонов Дмитрий Владимирович